You have no items in your shopping cart.
Catalog Advanced Search
344 item(s) were found using the following search criteria
- Manufacturer: Adafruit Industries
Don't see what you're looking for? Modify your search
-
Adafruit 12 x Capacitive Touch Shield for Arduino
This touch-able add on shield for Arduinos will inspire your next interactive project with 12 capacitive touch sensors. Learn More -
Adafruit PowerBoost 1000 Charger
This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects. Learn More -
Adafruit Bluefruit LE UART Friend - Bluetooth Low Energy (BLE)
Would you like to add powerful and easy-to-use Bluetooth Low Energy to your robot, art or other electronics project? Heck yeah! Learn More -
Adafruit DRV2605L Haptic Motor Controller
The DRV2605 from TI is a fancy little motor driver. Rather than controlling a stepper motor or DC motor, its designed specifically for controlling haptic motors - buzzers and vibration motors. Learn More -
Adafruit USB Isolator - 100mA Isolated Low/Full Speed USB
This handy little low-cost USB isolator is exactly what you need to provide protection against harmful noise, ground loops, surges, and spikes. Learn More -
Adafruit I2C Non-Volatile FRAM Breakout - 256Kbit / 32KByte
This particular FRAM chip has 256 Kbits (32 KBytes) of storage, interfaces using I2C, and can run at up to 1MHz I2C rates. Learn More -
Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit
HAT für den Raspberry Pi (alle Modelle) um 4 DC- oder 2 Stepper-Motoren mit vollem PCM-Support zu steuern. Learn More -
Adafruit Bluefruit LE SPI Friend - Bluetooth Low Energy (BLE)
The Bluefruit LE SPI Friend makes it easy to add Bluetooth Low Energy connectivity to anything with 4 or 5 GPIO pins. With SPI, you don't have to worry about baud rates, flow control, or giving up a hardware UART port Learn More -
Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger
Kleiner Charger für LiIon & LiPoly-Akkus 3.7V / 4.2V, mit MicroUSB-Anschluss Learn More -
Adafruit BMP280 I2C/SPI Barometer & Höhensensor (Stemma Qt)
Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! Learn More -
Adafruit PiTFT Plus 320x240 2.8" TFT + Touch - Assembled
Display featuring a 2.8" display with 320x240 16-bit color pixels and a capacitive touch overlay. Learn More -
Adafruit HUZZAH ESP8266 Breakout
The ESP8266 processor from Espressif is an 80 MHz microcontroller with a full WiFi front-end (both as client and access point) and TCP/IP stack with DNS support as well. Learn More -
Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055
Bosch is the first company to get this right by taking a MEMS accelerometer, magnetometer and gyroscope and putting them on a single die with a high speed ARM Cortex-M0 based processor. Learn More -
Bluefruit LE Friend - BLE 4.0 - nRF51822 - v3.0
This USB-to-BLE board makes it easy to get your computer talking to your BLE enabled phone or tablet using a standard serial/UART connection. Learn More -
Adafruit MPL115A2 - I2C Barometric Pressure/Temperature Sensor
I2C Druck/Temperatur-Sensor von Freescale Learn More -
Adafruit Pi-EzConnect Terminal Block Breakout HAT
Terminal Block HAT für alle Pi mit 40Pin GPIO Learn More -
Adafruit Bluefruit LE Shield - Bluetooth LE for Arduino
Would you like to add powerful and easy-to-use Bluetooth Low Energy to your robot, art or other electronics project? Heck yeah! Learn More -
Adafruit LM3671 3.3V Buck Converter Breakout - 3.3V/600mA
Your power supply problems just got SUPER SOLVED! This 3.3V Buck Converter Breakout board is great for supplying power to low voltage circuits from a single Li-Ion cell battery or USB power. Learn More -
Adafruit Wheel for Micro Continuous Rotation FS90R Servo
This black plastic Micro Continuos Rotation Servo Wheel is equipped with a silicone tire and a press-fit design to make connecting to your FS90R Micro Servo super quick and easy. Learn More -
Adafruit Monochrome 0.96" 128x64 OLED graphic display
These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Learn More -
Huzzah! Adafruit IOT Feather ESP8266 - WiFi Starter Kit
OK you've signed up for Adafruit.io and you're ready to build something cool and Internet-connected. All you need is this starter kit which will get you going with lots of parts that go very well with our service and are the most common sensors and actuators you may want. Learn More -
Adafruit Feather 32u4 Adalogger
Our take on an 'all-in-one' datalogger (or data-reader) with built in USB and battery charging. Its an Adafruit Feather 32u4 with a microSD holder ready to rock! Learn More -
Adafruit Silicon MEMS Microphone Breakout - SPW2430
Just like 'classic' electret microphones, MEMS mics can detect sound and convert it to voltage, but they don't need a bias resistor or amplifier, its all in one! Learn More -
Adafruit VCNL4010 Proximity/Light sensor
The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. Learn More -
Adafruit Feather HUZZAH with ESP8266 WiFi
This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8226 WiFi development board with built in USB and battery charging. Its an ESP8266 WiFi module with all the extras you need, ready to rock! Learn More -
Adafruit Feather 32u4 Basic Proto
Feather is the new development board from Adafruit, and like it's namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. Learn More -
Adafruit Feather M0 Basic Proto - ATSAMD21 Cortex M0
This is the Feather M0 (ATSAMD21 Cortex M0) Basic Proto, it has a bunch of prototyping space built right in. Learn More -
Adafruit FeatherWing Proto - Prototyping Add-on
A prototyping add-on for all Feather boards. Learn More -
Adafruit FeatherWing Doubler - Prototyping Add-on
The magic of the Doubler comes when stacking a Feather and another board on top of the Doubler so you can work with both boards simultaneously side-by-side! Learn More -
Feather Stacking Headers - 12-pin and 16-pin female headers
One 12- and one 16-Pin Stackable Header made for the Adafruit Feather Boards Learn More