You have no items in your shopping cart.
Breakout Boards
-
RJ45-Breakout with RJ45-Connector
RJ45-Breakout with RJ45-Connector Learn More -
Si7021 Humidity Sensor Breakout
The Si7021 is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor. Learn More -
SparkFun 6DoF IMU Breakout - LSM6DSV16X (Qwiic)
Looking for an extremely accurate way to detect motion utilizing AI? We've got you covered with the Qwiic-enabled, SparkFun LSM6DSV16X 6DoF IMU Breakout. Learn More -
SparkFun Analog/Digital MUX Breakout
Very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer with CD74HC4067 Learn More -
SparkFun Atmospheric Sensor Breakout - BME280 (with Headers)
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Learn More -
SparkFun Breakout Board for Electret Microphone
Ready to add audio to your next project? This small breakout board couples a small electret microphone with a 100x opamp to amplify the sounds of voice, door knocks, etc Learn More -
SparkFun Breakout Board for XBee Module
This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. Learn More -
SparkFun Brushless Motor Driver - 3-Phase (TMC6300)
The SparkFun 3-Phase Brushless Motor Driver, featuring the TMC6300 from ADI + Trinamic, is a powerful and easy-to-use three-phase motor driver. Learn More -
SparkFun Electric Imp Breakout
The Electric Imp Breakout Board allows you to explore the capabilities of the Imp by providing standard 0.1" headers to solder to as well as the necessary CryptAuthEE IC to identify your prototype to the Imp Cloud service! Learn More -
SparkFun Evaluation Board for Si4703 FM Tuner
Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. Learn More -
SparkFun FemtoBuck LED Driver
This is the FemtoBuck, a small-size single-output constant current LED driver. Learn More -
SparkFun Graphic LCD Serial Backpack
This is the serial backpack for graphic LCDs. The SparkFun Graphic LCD Serial Backpack interfaces to either our 160x128 pixel “Huge” Graphic LCD, or the smaller 128x64 pixel display Learn More -
SparkFun I2S Audio Breakout - MAX98357A
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S audio to an analog signal to drive speakers. Learn More -
SparkFun LED Array - 8x7
The SparkFun LED Array is a set of 56 red LEDs arranged in a nice 8x7 grid. Learn More -
SparkFun LED Tactile Button Breakout
This breakout board makes it easy to use our LED switches on a breadboard, or your next project Learn More -
SparkFun Level Shifter - Bi-Dir 8 Channel (TXS0108E)
The SparkFun 8 Channel Level Shifter Breakout features the TXS0108E™ 8-bit, bi-directional logic level translator from Texas Instruments. Learn More -
SparkFun LMV358 OpAmp Breakout
This is a simple Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). Learn More -
SparkFun Load Cell Amplifier - HX711
The SparkFun Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. Learn More -
SparkFun Load Sensor Combinator
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard 4-wire wheatstone configuration. Learn More -
SparkFun Logomatic v2 Serial SD Datalogger (FAT32)
The Logomatic v2 takes everything we learned with multiple logging projects over the years and boils it down to an easy to use device. Learn More -
SparkFun MOSFET Power Controller
This MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. Learn More -
SparkFun Multiplexer Breakout - 8 Channel (74HC4051)
The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. Learn More -
SparkFun Nano Power Timer - TPL5110
he SparkFun Nano Power Timer will run while only consuming minimal power (approximately 35nA) and turn your project on after a set amount of time. Learn More -
SparkFun OpenLog
OpenLog is an open source data logger. Simple to use, simple to change. Learn More -
SparkFun OpenLog Artemis
The SparkFun OpenLog Artemis is an open source data logger that comes preprogrammed to automatically log IMU, GPS, serial data, and various pressure, humidity, and distance sensors. Learn More -
SparkFun OpenLog Artemis (without IMU)
The SparkFun OpenLog Artemis is an open source data logger that comes preprogrammed to automatically log GPS, serial data, and various pressure, humidity, and distance sensors. Learn More -
SparkFun OpenScale
The SparkFun OpenScale is a simple-to-use, open source solution for measuring weight and temperature. Learn More -
SparkFun Opto-isolator Breakout
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. Learn More -
SparkFun Qwiic Haptic Driver - DA7280
The SparkFun Qwiic Haptic Driver includes an itty-bitty, Linear Resonant Actuator (LRA) vibration motor and Dialog Semiconductor's DA7280 motor driver IC for applications that require haptic feedback. Learn More -
SparkFun Real Time Clock Module DS1307 V1.4
This a custom designed module for the DS1307 Real Time Clock. Learn More
Breakout Boards
Minimal Price: 1.90