You have no items in your shopping cart.
Search results for 'I2c'
-
DK 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685
Erhalten Sie mit nur 2 Pins 16 unabhängige PWM-Ausgänge. Verbinden Sie bis zu 62 dieser Breakouts und erhalten Sie 992 PWM Ausgänge!
Learn More -
DK 16-Channel 12-bit PWM/Servo Shield - I2C interface
Using only two I2C pins, control 16 free-running PWM outputs! You can even stack up 62 shields to control up to 992 PWM outputs Learn More -
9DOF IMU with ADXL345, HMC5883L and ITG3205
9 Degrees of Freedom on one small board! Learn More -
GY Digitaler Ambient Light Sensor mit BH1750FVI
Messen Sie die Umgebungslichtstärke von 1 - 65535 Lux via I2C Learn More -
Adafruit MCP9808 High Accuracy I2C Temperature Sensor
This I2C digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range Learn More -
SparkFun T5403 Barometric Sensor Breakout
This is the T5403 breakout board, a fully calibrated barometric pressure sensor with an I2C interface. Learn More -
Atmel ATMEGA328P-AU - TQFP
ATMega 328 TQFP-Package. Without Arduino Bootloader! Learn More -
Adafruit GEMMA V2 - Miniature wearable electronic platform
Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project! Learn More -
Adafruit Quad Alphanumeric Display - Red, I2C
This is a nice, bright alphanumeric display that shows letters and numbers in a beautiful red hue. Learn More -
Adafruit Quad Alphanumeric Display - Blue, I2C
This is a nice, bright alphanumeric display that shows letters and numbers in a beautiful blue hue. Learn More -
Adafruit TXB0104 Bi-Directional Level Shifter
This chip perform bidirectional level shifting from pretty much any voltage to any voltage and will auto-detect the direction. Learn More -
Adafruit BMP183 SPI Barometric Pressure & Altitude Sensor
The BMP183 is the next-generation of sensors from Bosch, and is the fraternal twin of the BMP180. It has the same specifications, but uses SPI instead of I2C. Learn More -
Adafruit Analog UV Light Sensor Breakout - GUVA-S12SD
Extend your light-sensing spectrum with this analog UV sensor module. It uses a UV photodiode, which can detect the 240-370nm range of light (which covers UVB and most of UVA spectrum). Learn More -
9 Degrees of Freedom Breakout - MPU-9150
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. Learn More -
GY 10-DOF IMU Breakout - L3GD20 + LSM303 + BMP180
This inertial-measurement-unit combines 3 of the best quality sensors available on the market to give you 11 axes of data: 3 axes of accelerometer data, 3 axes gyroscopic, 3 axes magnetic (compass), barometric pressure/altitude and temperature. Learn More -
GPIO Extender Kabel for Raspberry PI F/F (40 Pin) 30cm
2 x 20 Pin Cable Female - Female, Length 30cm Learn More -
Adafruit Stereo 20W Class D Audio Amplifier - MAX9744
Pump up the volume with this 20W stereo amplifier! Learn More -
Adafruit Si5351A Clock Generator - 8KHz to 160MHz
This chip has a precision 25MHz crystal reference and internal PLL and dividers so it can generate just about any frequency, from <8KHz up to 150+ MHz. Learn More -
Contact-less Infrared Thermopile Sensor - TMP007
Contact-less Infrared Thermopile Sensor Breakout - TMP007 Learn More -
WaveShare SpotPear Expansionboard for Pi B+
Expansionshield for your Raspberry Pi Modell B+ Learn More -
LCD/Breadboard Set with Holder without Arduino
Set containing 1602-LCD (with I2C) as well as a Full-Size Breadboard, complete with an acrylic glas mounting plate. Learn More -
Mega LCD/Breadboard Set with Holder without Arduino
Set containing 0802-LCD as well as a Full-Size Breadboard, complete with an acrylic glas mounting plate. Learn More -
Adafruit Adafruit 12-Key Capacitive Touch Sensor
12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touch pads. Learn More -
Banana PI I2C GPIO Expansion Board
Das Board erweitert den Banana PI um 8 GPIO, ansprechbar mit I2C Learn More -
MCP23008 - 8 Port IO-Expander
MCP23008 - 8 Port IO-Expander Learn More -
Adafruit Quad Alphanumeric Display - Pure Green, I2C
This is a nice, bright alphanumeric display that shows letters and numbers in a beautiful green hue. Learn More -
Adafruit Quad Alphanumeric Display - Yellow , I2C
This is a nice, bright alphanumeric display that shows letters and numbers in a beautiful yellow hue. Learn More -
Adafruit Quad Alphanumeric Display - Yellow-Green, I2C
This is a nice, bright alphanumeric display that shows letters and numbers in a beautiful yellow-green hue. Learn More -
Adafruit Pi T-Cobbler Plus Kit - for Pi B+ - Assembled
The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the B+ that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header. Learn More -
Tinkerforge RED Brick
The Rapid Embedded Development Brick (RED Brick) can control other Bricks and Bricklets. Learn More
